首页
登录
职称英语
Tacoma Narrows Bridge Disaster Strikes When the Tacoma Narrows
Tacoma Narrows Bridge Disaster Strikes When the Tacoma Narrows
游客
2025-02-17
8
管理
问题
Tacoma Narrows Bridge Disaster Strikes
When the Tacoma Narrows Bridge opened for traffic on 1 July 1940, it was celebrated as a major engineering achievement. Even before construction was completed, however, flaws in the design were apparent; workers sucked on lemon slices to avoid motion sickness as the structure swayed in the relatively mild winds. Engineers tried three different revisions during construction to address the vibration problem. Initially, fie-down cables were anchored to fifty-tone bulkheads on the river banks. These were ineffective, as the cables soon detached. Then a pair of inclined cable locks was introduced to connect the main cables to the bridge deck at mid-span. These stayed throughout the bridge’s lifespan, but did nothing to reduce vibration. A further measure—the installation of hydraulic dampers between the towers and the floor system—was nullified because the dampers were compromised when the bridge was sand-blasted before painting.
Shortly after opening, the bridge quickly acquired the fond nickname of "Galloping Gertie" because of the way it would roll in either side-to-side or length-ways movements—known in physics terms as the longitudinal and transverse modes of vibration respectively. These movements did not compromise the core integrity of the structure, but did make the crossing a somewhat white-knuckle affair. Many drivers reported seeing cars ahead disappear from sight several times as they sank into troughs from transverse vibrations (imagine the ripple across a packed stadium during a Mexican wave ). The experience of a longitudinal wave is closely analogous, but more accurately associated with the waves one would encounter in the ocean. On a suspension bridge though, these waves are a unique experience—some dare-devils were happy to pay the 75c toll just for the thrill!
Four months later, however, a never-before-seen type of vibration began afflicting the bridge in what were still fairly gentle winds (about 40 kemp). Rather than the simple "wave" motion that characterizes longitudinal and transverse vibration, the left side of the bridge would rise while the right side fell, but the centre line of the road would remain completely level. This was proved when two men walked along the centre of the bridge completely unaffected by the rocking motions around them. Visually the bridge’s movements seemed to be more like a butterfly flapping its wings than a simple rolling motion. Engineers now understand this to be the tensional mode of vibration, and it is extremely hard to detect. In aero plane design, for example, even minute shifts of the aircraft’s mass distribution and an alteration in one component can affect a component with which it has no logical connection. In its milder forms this can cause a light buzzing noise, similar to that which a wasp or a bumble bee makes, but when allowed to develop unchecked it can eventually cause the total destruction of an aero plane.
The tensional mode of vibration is the consequence of a set of actions known as aerostatic flutter. This involves several different elements of a structure oscillating from the effect of wind, with each cycle of fluttering building more energy into the bridge’s movements and neutralizing any structural damping effects. Because the wind pumps in more energy than the structure can dissipate, and the oscillations feed off each other to become progressively stronger, the aerostatic fluttering and tensional vibrations were all but assured to destroy the Tacoma Bridge on the morning of 7 November. At 11.00 a.m. the fluttering had increased to such amplitude that the suspender cables were placed under excessive strain. When these buckled, the weight of the deck transferred to the adjacent cables which in turn were unable to support the weight. These cables buckled, leaving nothing to stop the central deck breaking off into the Tacoma River.
It was at around 10.15 a.m. on 7 November that tensional vibration began afflicting the bridge. This made driving treacherous, and newspaper editor Leonard Coats worth’s car was jammed against the curb in the centre of the bridge as he attempted to cross. Coats worth tried to rescue his daughter’s cocker spaniel from the back seat but was unsuccessful, and fearing for his life, crawled and staggered to safety on his own. At this point, an engineering professor named Bert Farquharson proceeded onto the bridge in an attempt to save the frightened animal. Farquharson had been video-recording from the banks of the fiver and had just returned from purchasing more rolls of film. As an avowed dog lover he felt obliged to attempt a rescue. Unfortunately, the professor too was bitten and retreated empty handed, walking off just moments before the cables snapped and the giant concrete mass of the central deck caved inwards and disappeared into the fiver.
Questions 14-16
Complete the notes below.
Choose NO MORE THAN TWO WORDS from the passage for each answer.
Write your answers in boxes ]4-16 on your answer sheet.
Engineers used various techniques while building the bridge to reduce wobble:
they attached (14) to heavy blocks on the shoreline
they fastened main cables to the middle of the (15)
(16) were placed between the tallest parts of the structure and the deck. [br]
选项
答案
tie-down cables
解析
转载请注明原文地址:https://tihaiku.com/zcyy/3960971.html
相关试题推荐
TacomaNarrowsBridgeDisasterStrikesWhentheTacomaNarrows
TacomaNarrowsBridgeDisasterStrikesWhentheTacomaNarrows
TacomaNarrowsBridgeDisasterStrikesWhentheTacomaNarrows
随机试题
Idon’tthinkyouhaveheardofthestorybeforeyouknewPeter,______A、don’tI
Wecanmakemistakesatanyage.Somemistakeswemakeareaboutmoney.But
[originaltext]Chinahasneverhiddenitsdesiretobecomeamajorforcein
路由器是在( )实现网络互联的设备。A.网络层 B.数据链路层 C.物理层
在汇总记账凭证账务处理程序下,平时编制记账凭证时可以填制()。A、一借一贷转账
在社区精神疾病患者的心理治疗工作中,下列最重要的原则是A:必须详细地收集病史,包
宋江、林冲和武松各自买了一辆汽车,分别是宝马、奥迪和陆虎。关于他们购买的品牌,吴
下列气体灭火剂中,灭火中有化学抑制作用的是()。A.二氧化碳 B.IG5
甲村为了灌溉A土地,与乙村签订了书面合同,约定甲村每年支付乙村1万元,甲村在乙村
除高频电阻焊除外,一般压焊都采用()。A.对接接头 B.搭接接头 C.
最新回复
(
0
)